Cad/cam veneers

OBJECTIVE: To analyze the influence of restoration design (partial-coverage restoration vs. crown) and ceramic layer thickness on the performance and failure loads of CAD/CAM-fabricated lithium disilicate (LDS) reconstructions on molars after fatigue. MATERIALS AND METHODS: Seventy-two posterior monolithic CAD/CAM-fabricated LDS restorations (IPS e.max CAD, Ivoclar Vivadent) with different occlusal/buccal ceramic layer thicknesses (1.5/0.8, 1.0/0.6, and 0.5/0.4 mm) and restoration designs (PCR: non-retentive full-veneer/partial-coverage restoration, C: crown,) were investigated and divided into six groups (n = 12, test: PCR-1...

PURPOSE: To evaluate the survival of and incidence of mechanical complications with single- and multiple-unit cement-retained posterior implant-supported restorations with custom CAD/CAM Atlantis titanium abutments (Dentsply Sirona, Charlotte, NC, USA). MATERIALS AND METHODS: This retrospective clinical study analysed 196 Astra Tech OsseoSpeed TX Internal Hexagon implants (Dentsply Sirona) placed in 85 patients between January 2011 and January 2021. Customised Atlantis titanium abutments and cement-retained metal-ceramic crowns were employed...

Autotransplanted teeth in the maxillary anterior region should be restored or reshaped as soon as possible for functional and esthetic reasons as well as the well-being of the patient. However, such tooth restorations are frequently not carried out immediately after tooth transplantation because the process could have a negative impact on the healing process. The development of a simple, immediate, and atraumatic esthetic interim restoration would be of great benefit to both the clinician and patient and address all the concerns caused by immediately preparing the tooth postoperatively and cementing a permanent restoration...

OBJECTIVE: This article highlights the feasibility of the additive fabrication of ultra-thin veneers made of lithium disilicate using the lithography-based ceramic manufacturing (LCM) method. CLINICAL CONSIDERATIONS: An esthetical appealing restoration of anterior teeth with thin ceramic veneers is considered one of the ultimate challenges in restorative dental prosthetics. These sophisticated restorations can be fabricated in different ways. Both analog and digital subtractive manufacturing processes have been used to date...

PURPOSE: The purpose of this in vitro study was to analyze the shear bond strength of composite resin to a commercially available high-performance polymer material for fixed, screw-retained full arch restorations. MATERIAL AND METHODS: 135 computer-aided design and computer-aided manufacturing, high-performance polymer (HPP) blocks were cut and obtained from discs (Trilor 95, Harvest Dental, Brea, CA). The samples were 10 mm × 10 mm × 10 mm. The specimen surfaces were grouped as untreated (Group A), 50 μm Al2O3 (Group B), 110 μm Al2O3 (Group C), Rocatec (3M, St...

PURPOSE: The purpose of this study was to assess the effect of resin cement shade on the color of different novel ultratranslucent monolithic zirconia and lithium disilicate veneer materials. MATERIALS AND METHODS: For a total of 40 specimens, flat cylindrical discs with a 9-mm diameter and 0.5-mm thickness were created using CAD/CAM technology. The specimens were divided into five groups according to their material (n = 8) (e.max, Prettau, Aidite, Shofu and Dima) using A1 shade...

The aim of the present study was to evaluate the influence of two different internal surface treatments, namely, the firing of feldspathic porcelain before or after zirconia sintering, on the marginal and internal adaptation of laminate veneers (LVs) made of high-translucent zirconia. A total of 33 zirconia LVs were fabricated using a CAD/CAM system and divided into three groups based on the internal surface treatment method: the pre-firing (PRE) group involved firing feldspathic porcelain before zirconia sintering, the post-firing (POS) group involved firing feldspathic porcelain after zirconia sintering, and the no treatment (NT) group involved no application of feldspathic porcelain...

PURPOSE: To compare the masking ability of monolithic CAD-CAM veneers placed over different resin cement shades and substrate colors. MATERIAL AND METHODS: Veneers were milled of four different monolithic CAD-CAM restorative materials: feldspathic ceramic (VMII), lithium disilicate ceramic (Emax CAD), zirconia-reinforced lithium silicate ceramic (VS), and high translucency zirconia ceramic (YZ-XT). Veneers (n=9) were luted on natural tooth colored (ND1) or discolored substrates (ND3 or ND5) using two different resin cement shades (white opaque or translucent)...

PURPOSE: The purpose of the study was to assess the clinical performance of CAD-CAM laminate veneers placed by a single operator and systematically evaluated for up to 10 years. MATERIAL AND METHODS: A total of 197 laminate veneers fabricated using either feldspathic ceramic (VMII) or lithium disilicate ceramic (EmaxCAD) were followed up to 10 years in 32 patients. Technical, esthetical, and biological findings of each restoration were evaluated using modified United States Public Health Service criteria...

Chipping of implant-supported molar crowns (iSCs) is a frequently reported complication. This study aimed to investigate the in-vitro aging and fracture resistance of iSCs with a CAD/CAM resin composite veneer structure fabricated with the Rapid Layer Technology (RLT) approach. Eight iSCs per group were fabricated by using two different CAD/CAM resin composites (Shofu Block HC: SH; Grandio blocs: GB) for veneer structures, and zirconia (ZrO2 ), polyetheretherketone (PEEK), and cobalt-chromium (CoCr; control) as framework materials...

Background: Er:YAG laser is widely used in debonding of all-ceramic veneers nowadays. However, the data about laser parameters in all-ceramic crown removal is limited. The aim of this preliminary study was to determine the most appropriate laser parameters at safe heat transmission values ​​for lithium disilicate crowns in different thicknesses. Methods: Twenty-seven intact premolars were prepared to fabricate lithium disilicate CAD/CAM full-coverage crowns in three different thicknesses: 1, 1...

BACKGROUND: Insufficient research has been conducted in the literature assessing the performance of zirconia and polyetheretherketone (PEEK) crowns in relation to the essential requirements of successful restorations, such as fracture resistance or margin adaptation. The purpose of this study was to evaluate the effect of the coping materials zirconia or PEEK with different fabrication techniques on the vertical marginal gap and fracture resistance of posterior crowns with composite veneering...

PURPOSE: The aim of this in-vitro study was to evaluate the effect of thermal changes to shear bond strength during the firing process of veneering porcelain on a zirconia framework. MATERIALS AND METHODS: Single yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) framework ceramic (Kavo Dental GmbH) and three different types of veneering ceramics (IPS e.max Ceram, Vita VM9, and GC Initial Zr-FS) were used. One-hundred-twenty standard disc-shaped samples were prepared from zirconia blocks by using a CAD/CAM system (Kavo Everest)...

OBJECTIVE: To evaluate the effects of cusp inclination of the prosthetic preparation's occlusal surface and type of restorative material on the fatigue behavior, failure mode, and stress distribution of occlusal veneers. MATERIALS AND METHODS: Glass fiber-reinforced epoxy resin prosthetic preparations for occlusal veneers with three different occlusal surface cusp inclination degrees (0°, 15°, and 30°) were produced and assigned into six testing groups (n = 11) according to the cusp inclination (0°, 15°, or 30°) and type of restorative material (lithium disilicate-LD or resin composite-RC)...

OBJECTIVES: The aim was to assess how incorporating a short-fiber composite (SFC) core would affect the fracture behavior of direct and indirect overlays. Furthermore, to examine the relationship between the thickness ratio of SFC core to particulate-filled composite (PFC) veneering and the fracture-behavior of bilayered-structured restorations. MATERIALS AND METHODS: A total of 120 molars were used to create MOD cavities, with palatal cusps removed. Four different groups of direct overlays were then made (n = 15/group), all of which featured a SFC core (everX Flow) with varying thicknesses (0, 1, 4, and 5 mm), as well as a surface layer of PFC (G-aenial Posterior), with the overall thickness of the bilayered-structured restoration set at 5 mm...

OBJECTIVE: This in-vitro study is planned to analyze the effect of different thicknesses of ceramic occlusal veneers and different surface treatments on fracture resistance. MATERIALS AND METHODS: A total of 48 sound mandibular molars are anatomically prepared from the occlusal surface with two different thicknesses (1.0 and 0.5 mm). CAD/CAM zirconia-reinforced glass ceramic blocks (Vita Suprinity) are used for fabricating occlusal veneers. The teeth are randomly divided into two primary groups A and B (n=24) according to occlusal veneer thickness...

PURPOSE: To evaluate the vertical misfit, stress distribution around dental implants, and cantilever fracture strength of 3-unit implant-supported cantilever fixed partial dentures (FPDs) using frameworks made from different materials and manufacturing techniques. MATERIALS AND METHODS: Forty FPDs were fabricated and divided into 5 groups (n = 8) based on the framework material used: G1 - LAS Co-Cr (Conventional casting - laser welding); G2 - TIG Co-Cr (Conventional casting -TIG welding); G3 - OP Co-Cr (Conventional casting - one-piece); G4 - CAD Co-Cr (CAD-CAM); and G5 - CAD Zr (CAD-CAM ZrO2 )...

OBJECTIVES: Ceramic-sintering affects bond strength and longevity of metal-ceramic. This study investigated the effect of sintering temperatures and times on metal-ceramic bond strength vis-a-vis interfacial fracture toughness. MATERIALS AND METHODS: One hundred eighty rectangular-shaped (25 × 8 × 1 mm) casting (Auriloy® (CA)) and CAD-milling (Ceramill Sintron® (MA)) alloys were prepared and randomly veneered with ceramic at normal (930 °C; (TN)), increased (940 °C; (TI)), and extremely increased (950 °C; (TE)) sintering temperatures and normal (1 min; (HN)), increased (2 min; (HI)), and extremely increased (3 min; (HE)) sintering time (n = 10/group)...

Background and Objective: This study aimed to compare the surface finish of milled leucite-reinforced ceramics polished with ceramic and composite polishing systems based on the manufacturers' recommendations. Materials and Methods: Sixty subtractive computer-aided manufactured (s-CAM) leucite-reinforced glass-ceramic specimens (IPS-Empress-CAD) were assigned into six groups: no polishing, a ceramic polishing kit, and four composite kit groups. The roughness average (Ra) was evaluated in microns using a profilometer, and scanning electron micrographs were obtained for qualitative analysis...

This study aimed to investigate the effects of two antioxidants and their application time on the fracture strength of computer-aided design and computer-aided manufacturing (CAD/CAM)-fabricated ceramic laminate veneers to bleached enamel, as well as their effects on the bonding interface micromorphology. Eight groups were set: Group NC (without bleaching and antioxidant treatment); Group NA (bleaching without antioxidant treatment); Group SA30, SA60, SA120 and Group PAC30, PAC60, PAC120 (bleaching and treating with sodium ascorbate or proanthocyanidins for 30, 60, and 120 min, respectively)...