keyword
MENU ▼
Read by QxMD icon Read
search

Cad/cam veneers

keyword
https://www.readbyqxmd.com/read/28091875/the-effect-of-veneering-on-the-marginal-fit-of-cad-cam-generated-copy-milled-and-cast-metal-copings
#1
Sabit Melih Ates, Zeynep Yesil Duymus, Ipek Caglar, Bilal Hologlu
OBJECTIVE: This in vitro study investigated the marginal fit of metal and zirconia copings before and after veneering on dies with shoulder/chamfer (s/c) finish lines. MATERIALS AND METHODS: Using CAD/CAM, ten (n = 10) each s/c zirconia (NZ) copings and ten (n = 10) each s/c metal (MM) copings were generated. As controls, ten (n = 10) each s/c zirconia copings were copy-milled (ZZ) and ten (n = 10) each s/c metal copings were cast (CC). The vertical marginal discrepancy of the copings was measured at 20 predefined spots of the circular shoulder and chamfer finish lines in microns (μm) before and after a first and a second veneering firing using a stereomicroscope at ×40 magnification...
January 13, 2017: Clinical Oral Investigations
https://www.readbyqxmd.com/read/28070702/effects-of-tributylborane-activated-adhesive-and-two-silane-agents-on-bonding-computer-aided-design-and-manufacturing-cad-cam-resin-composite
#2
Ayano Shinohara, Yohsuke Taira, Takashi Sawase
The present study was conducted to evaluate the effects of an experimental adhesive agent [methyl methacrylate-tributylborane liquid (MT)] and two adhesive agents containing silane on the bonding between a resin composite block of a computer-aided design and manufacturing (CAD/CAM) system and a light-curing resin composite veneering material. The surfaces of CAD/CAM resin composite specimens were ground with silicon-carbide paper, treated with phosphoric acid, and then primed with either one of the two silane agents [Scotchbond Universal Adhesive (SC) and GC Ceramic Primer II (GC)], no adhesive control (Cont), or one of three combinations (MT/SC, MT/GC, and MT/Cont)...
January 9, 2017: Odontology
https://www.readbyqxmd.com/read/28018561/comparison-of-the-fit-accuracy-of-zirconia-based-prostheses-generated-by-two-cad-cam-systems
#3
Seok-Joon Ha, Jin-Hyun Cho
PURPOSE: The purposes of this study are to evaluate the internal and marginal adaptation of two widely used CAD/CAM systems and to study the effect of porcelain press veneering process on the prosthesis adaptation. MATERIALS AND METHODS: Molar of a lower jaw typodont resin model was prepared by adjusting a 1.0 mm circumferential chamfer, an occlusal reduction of 2.0 mm, and a 5° convergence angle and was duplicated as an abrasion-resistant master die. The monolithic crowns and copings were fabricated with two different CAD/CAM system-Ceramil and Zirkonzahn systems...
December 2016: Journal of Advanced Prosthodontics
https://www.readbyqxmd.com/read/27927884/esthetic-and-clinical-performance-of-implant-supported-all-ceramic-crowns-made-with-prefabricated-or-cad-cam-zirconia-abutments-a-randomized-multicenter-clinical-trial
#4
J G Wittneben, J Gavric, U C Belser, M M Bornstein, T Joda, V Chappuis, I Sailer, U Brägger
Patients' esthetic expectations are increasing, and the options of the prosthetic pathways are currently evolving. The objective of this randomized multicenter clinical trial was to assess and compare the esthetic outcome and clinical performance of anterior maxillary all-ceramic implant crowns (ICs) based either on prefabricated zirconia abutments veneered with pressed ceramics or on CAD/CAM zirconia abutments veneered with hand buildup technique. The null hypothesis was that there is no statistically significant difference between the 2 groups...
December 7, 2016: Journal of Dental Research
https://www.readbyqxmd.com/read/27890357/effect-of-cement-space-on-stress-distribution-in-y-tzp-based-crowns
#5
Carlos Eduardo Edwards Rezende, Ana Flávia Sanches Borges, Carla Castiglia Gonzaga, Yuanyuan Duan, José Henrique Rubo, Jason Alan Griggs
OBJECTIVE: To evaluate the stress distribution in bi-layered Y-TZP based crowns, according to the occlusal internal spacing between coping and abutment. METHODS: Twelve premolar shaped Y-TZP copings were made by a CAD/CAM system and seated on an abutment to evaluate the internal fit at the occlusal third using micro-CT images. Considering the fitting range obtained experimentally, two 3D finite element models, consisting on bone tissue, a titanium implant, a zirconia abutment, cement layer and a bi-layered Y-TZP ceramic crown were constructed based on the micro-CT images, one corresponding to the thinnest cement space and other representing the specimen with the thickest cement space obtained experimentally...
November 24, 2016: Dental Materials: Official Publication of the Academy of Dental Materials
https://www.readbyqxmd.com/read/27870167/design-of-complete-dentures-by-adopting-cad-developed-for-fixed-prostheses
#6
Yanfeng Li, Weili Han, Jing Cao, Yuan Iv, Yue Zhang, Yishi Han, Yi Shen, Zheng Ma, Huanyue Liu
The demand for complete dentures is expected to increase worldwide, but complete dentures are mainly designed and fabricated manually involving a broad series of clinical and laboratory procedures. Therefore, the quality of complete dentures largely depends on the skills of the dentist and technician, leading to difficulty in quality control. Computer-aided design and manufacturing (CAD/CAM) has been used to design and fabricate various dental restorations including dental inlays, veneers, crowns, partial crowns, and fixed partial dentures (FPDs)...
November 21, 2016: Journal of Prosthodontics: Official Journal of the American College of Prosthodontists
https://www.readbyqxmd.com/read/27866055/microstructure-and-nanoindentation-analyses-of-low-temperature-aging-on-the-zirconia-porcelain-interface
#7
M D Peng, J Q Wei, Y N Wang, Q Li
The aim of the present study was to investigate the effects of low-temperature aging on the micro-mechanical and micro-structural properties of zirconia-porcelain interface. In total, thirty-three Y-TZP zirconia blocks were fabricated by using CAD/CAM technology, veneered with porcelains. Specimens were submitted to low-temperature aging in an autoclave at 134°C, additional 0.2MPa pressure for 0h, 5h, or 10h. Flexural strength was obtained by using three-point bending test. Micro-mechanical properties (nano-hardness (H) and reduced modulus (Er)) were investigated by nanoindentation tests...
February 2017: Journal of the Mechanical Behavior of Biomedical Materials
https://www.readbyqxmd.com/read/27796072/time-efficiency-analysis-of-the-treatment-with-monolithic-implant-crowns-in-a-digital-workflow-a-randomized-controlled-trial
#8
Tim Joda, Urs Brägger
OBJECTIVES: The aim of the randomized controlled trial was to analyze time-efficiency of a treatment with implant crowns made of monolithic lithium disilicate (LS2) plus titanium base vs. porcelain fuse to zirconium dioxide (ZrO2 ) in a digital workflow. MATERIALS AND METHODS: Twenty study participants were included for single-tooth replacement in premolar and molar sites. Baseline was the start of the prosthetic treatment. All patients received transocclusal screw-retained implant reconstructions on a soft tissue level-type implant...
November 2016: Clinical Oral Implants Research
https://www.readbyqxmd.com/read/27671466/fatigue-behavior-of-resin-modified-monolithic-cad-cam-rnc-crowns-and-endocrowns
#9
G T Rocca, P Sedlakova, C M Saratti, R Sedlacek, L Gregor, N Rizcalla, A J Feilzer, I Krejci
OBJECTIVE: To evaluate the influence of different types of modifications with resin on fatigue resistance and failure behavior of CAD-CAM resin nano ceramic (RNC) restorations for maxillary first premolars. METHODS: Sixty standardized resin composite root dies received CAD-CAM RNC endocrowns (n=30) and crowns (n=30) (Lava Ultimate, 3M Espe). Restorations were divided into six groups: full anatomic endocrowns (group A) and crowns (group D), buccal resin veneered endocrowns (group B) and crowns (group E) and buccal resin veneered endocrowns (group C) and crowns (group F) with a central groove resin filling...
December 2016: Dental Materials: Official Publication of the Academy of Dental Materials
https://www.readbyqxmd.com/read/27671465/porcelain-bonding-to-novel-co-cr-alloys-influence-of-interfacial-reactions-on-phase-stability-plasticity-and-adhesion
#10
Kai Chun Li, LeYing Tran, David J Prior, J Neil Waddell, Michael V Swain
OBJECTIVE: The objective of the present study was to determine the hardness and adhesion strength at the porcelain to alloy interface. METHODS: 15 bi-layer porcelain veneered Co-Cr specimens of each alloy group [cast, powder metallurgy (PM), CAD/CAM(CC)] were manufactured. 12 bi-layered specimens were tested using four-point bend strain energy release rate adhesion test. One before and after porcelain firing specimen of each alloy group were nano-indented at the bulk and metal-porcelain interface to determine the mechanical properties...
December 2016: Dental Materials: Official Publication of the Academy of Dental Materials
https://www.readbyqxmd.com/read/27668099/esthetic-rehabilitation-through-crown-lengthening-surgery-and-conservative-cad-cam-veneers-a-multidisciplinary-case-report
#11
Leandro Passos, Fernando Peixoto Soares, Mauricio Gallo
This case report describes a successful multidisciplinary approach used to improve the smile esthetics of a patient presenting with excessive gingival display, asymmetric gingival margins, and small upper anterior teeth and lower anterior teeth. The treatment combined esthetic crown lengthening, dental bleaching, and restorative dentistry using CAD/CAM veneer. The 6-month follow-up examination confirmed the stability of the modification and absence of adverse effects.
2016: Case Reports in Dentistry
https://www.readbyqxmd.com/read/27595717/effect-of-repeated-firings-on-microtensile-bond-strength-of-bi-layered-lithium-disilicate-ceramics-e-max-cad-and-e-max-press
#12
Hamid Jalali, Zeinab Bahrani, Somayeh Zeighami
AIM: To achieve acceptable contour, color, esthetics, and occlusal relations, the porcelain may be subjected to several firing cycles. This study sought to assess the effect of multiple firing cycles on the microtensile bond strength (MTBS) of lithium disilicate-based ceramics (e.max Press, e.max CAD). MATERIALS AND METHODS: IPS e.max computer aided design (CAD) cores were fabricated using CAD/(Computer Aided Manufacturing (CAM)) technology, and IPS e.max Press cores were fabricated using the heat-pressing technique (12 × 12 × 4 mm(3))...
July 1, 2016: Journal of Contemporary Dental Practice
https://www.readbyqxmd.com/read/27570943/retrospective-2-to-7-year-follow-up-study-of-20-double-full-arch-implant-supported-monolithic-zirconia-fixed-prostheses-measurements-and-recommendations-for-optimal-design
#13
Fernando Rojas Vizcaya
PURPOSE: To measure the extension of cantilever lengths, thicknesses, and heights of zirconia prostheses in the lingual and facial areas of the distal screw access openings, and to evaluate the clinical performance regarding chipping or fracture of the distal cantilevered sections of double full-arch CAD/CAM screw-retained, stained, monolithic zirconia, gingival-colored ceramic implant-supported fixed prostheses (MZ-FPs). MATERIALS AND METHODS: Ten edentulous patients were provided with a total of 20 CAD/CAM double full-arch MZ-FPs...
August 29, 2016: Journal of Prosthodontics: Official Journal of the American College of Prosthodontists
https://www.readbyqxmd.com/read/27559346/comparison-of-marginal-fit-and-fracture-strength-of-a-cad-cam-zirconia-crown-with-two-preparation-designs
#14
Hamid Jalali, Leyla Sadighpour, Ali Miri, Ahmad Reza Shamshiri
OBJECTIVES: The purpose of this in vitro study was to compare the marginal adaptation and fracture resistance of a zirconia-based all-ceramic restoration with two preparation designs. MATERIALS AND METHODS: Twenty-four mandibular premolars were randomly divided into two groups (n=12); the conventional group received a peripheral shoulder preparation and the modified group received a buccal shoulder and proximal/lingual chamfer preparation. The marginal fit of the zirconia crowns (Cercon) was evaluated using a stereomicroscope...
December 2015: Journal of Dentistry of Tehran University of Medical Sciences
https://www.readbyqxmd.com/read/27507992/in-vitro-effect-of-porcelain-firing-cycle-and-different-thicknesses-of-ips-e-max-cad-core-on-marginal-accuracy-of-all-ceramic-restorations
#15
Ezatollah Jalalian, Arash Zarbakhsh, Zahra Mohtashamrad, Nazanin Nourbakhsh, Esmat Jafarpour
OBJECTIVES: Marginal adaptation is important for long-term success of full-coverage restorations. The aim of this study was to determine the effect of porcelain firing cycle and different thicknesses of IPS e.max core on marginal accuracy of all-ceramic restorations. MATERIALS AND METHODS: A standard stainless steel die with 0.8 mm classic chamfer finish line and 10° taper was used in this in vitro study. An impression was taken from the stainless steel die to fabricate 20 epoxy resin dies, which were then scanned and IPS e...
November 2015: Journal of Dentistry of Tehran University of Medical Sciences
https://www.readbyqxmd.com/read/27478442/a-new-total-digital-smile-planning-technique-3d-dsp-to-fabricate-cad-cam-mockups-for-esthetic-crowns-and-veneers
#16
F Cattoni, F Mastrangelo, E F Gherlone, G Gastaldi
Purpose. Recently, the request of patients is changed in terms of not only esthetic but also previsualization therapy planning. The aim of this study is to evaluate a new 3D-CAD-CAM digital planning technique that uses a total digital smile process. Materials and Methods. Study participants included 28 adult dental patients, aged 19 to 53 years, with no oral, periodontal, or systemic diseases. For each patient, 3 intra- and extraoral pictures and intraoral digital impressions were taken. The digital images improved from the 2D Digital Smile System software and the scanner stereolithographic (STL) file was matched into the 3D-Digital Smile System to obtain a virtual previsualization of teeth and smile design...
2016: International Journal of Dentistry
https://www.readbyqxmd.com/read/27273727/modified-peek-resin-bonded-fixed-dental-prosthesis-for-a-young-cleft-lip-and-palate-patient
#17
Efstathia Andrikopoulou, Panagiotis Zoidis, Ioli-Ioanna Artopoulou, Asterios Doukoudakis
OBJECTIVE: This clinical report presents the use of a modified poly ether-ether ketone material as an alternative material for the fabrication of resin-bonded fixed dental prosthesis (RBFDP) framework. This new material can be used for patients allergic to metals, maintaining the same high esthetic demand of ceramics, presenting light weightness and a flexibility similar to bone as a distinct advantage over ceramic materials. CONCLUSIONS: The use of a BioHPP RBFDP framework could be considered as an alternative restoration for the replacement of missing lateral incisors in young patients with cleft palate defects...
July 2016: Journal of Esthetic and Restorative Dentistry
https://www.readbyqxmd.com/read/27266201/-influence-of-different-designs-and-porcelain-glaze-firing-on-the-marginal-and-internal-fit-of-implant-supported-zirconia-crowns
#18
Liu Cuiling, Gao Xu, Qi Yuping, Yang Liyuan
OBJECTIVE: This study investigated the influence of different designs and porcelain/glaze firing on the marginal and internal fit of three kinds of computer aided design/computer aided manufacturing (CAD/CAM) zirconia ceramic implant-supported crowns. METHODS: Three groups of zirconia ceramic implant-supported crowns with different designs were produced from copings by using a Cercon CAD/CAM system (n = 8). The first two groups comprised double-layer crowns (zirconia coping + veneer) with regular (Group A) and full circumferential zirconia-collar marginal designs (Group B)...
February 2016: Hua Xi Kou Qiang Yi Xue za Zhi, Huaxi Kouqiang Yixue Zazhi, West China Journal of Stomatology
https://www.readbyqxmd.com/read/27163490/veneered-zirconia-based-restorations-fracture-resistance-analysis
#19
Ahed Al-Wahadni, Ahmad Shahin, Kenneth S Kurtz
PURPOSE: To examine the effects of the veneering technique on the fracture resistance of zirconia-based crowns. MATERIALS AND METHODS: An artificial tooth was prepared with a 1.2 mm heavy chamfer finish line and 8° taper. The prepared tooth was scanned using CAD/CAM technology to fabricate 45 cobalt chromium (CoCr) testing dies. One CoCr die was scanned, and 45 zirconia copings were milled and divided according to the veneering technique into three groups of 15 specimens each: layering veneering (LV) using Vita Vm9, overpressing veneering (OV) using Vita Pm9, and digital veneering (DV) using Vita Triluxe forte...
May 10, 2016: Journal of Prosthodontics: Official Journal of the American College of Prosthodontists
https://www.readbyqxmd.com/read/27159089/an-in-vitro-investigation-of-veneered-zirconia-based-restorations-shade-reproducibility
#20
Ahed Al-Wahadni, Ahmad Shahin, Kenneth S Kurtz
PURPOSE: To examine the effects of the veneering technique on the shade reproducibility of zirconia-based crowns. MATERIALS AND METHODS: An artificial tooth was prepared with a 1.2 mm heavy chamfer finish line and 8° taper. The prepared tooth was scanned using CAD/CAM technology to fabricate 45 cobalt chromium (CoCr) testing dies. One CoCr die was scanned, and 45 zirconia copings were milled and devided according to the veneering technique into 3 groups of 15 specimens each: layering veneering (LV) using Vita Vm9, overpressing veneering (OV) using Vita Pm9, and digital veneering (DV) using Vita Triluxe forte...
May 9, 2016: Journal of Prosthodontics: Official Journal of the American College of Prosthodontists
keyword
keyword
15705
1
2
Fetch more papers »
Fetching more papers... Fetching...
Read by QxMD. Sign in or create an account to discover new knowledge that matter to you.
Remove bar
Read by QxMD icon Read
×

Search Tips

Use Boolean operators: AND/OR

diabetic AND foot
diabetes OR diabetic

Exclude a word using the 'minus' sign

Virchow -triad

Use Parentheses

water AND (cup OR glass)

Add an asterisk (*) at end of a word to include word stems

Neuro* will search for Neurology, Neuroscientist, Neurological, and so on

Use quotes to search for an exact phrase

"primary prevention of cancer"
(heart or cardiac or cardio*) AND arrest -"American Heart Association"