Stress fractures

PURPOSE: To study the association between meat intake (predominantly red and processed meats) and the risk of hip fracture, as well as the association between meat intake and biomarkers of inflammation, oxidative stress, bone turnover, body composition, and bone mineral density (BMD). METHODS: Data from the Swedish Mammography Cohort and the Cohort of Swedish men (n = 83,603, 54% men) with repeated investigations and their respective clinical sub-cohorts was utilised...

PURPOSE: The toughest challenge in pedestrian traffic accident identification lies in ascertaining injury manners. This study aimed to systematically simulate and parameterize 3 types of craniocerebral injury including impact injury, fall injury, and run-over injury, to compare the injury response outcomes of different injury manners. METHODS: Based on the Total Human Model for Safety (THUMS) and its enhanced human model THUMS-hollow structures, a total of 84 simulations with 3 injury manners, different loading directions, and loading velocities was conducted...

Stress fractures, a common overuse injury in physically active individuals, present a significant challenge for athletes and military personnel. Patients who sustain stress fractures have demanding training regimes, where periods of rest and immobilisation have unacceptable negative consequences on sport goals and finances. Aside from being an overuse injury, there are various contributing risk factors that put certain individuals at risk of a stress fracture. The main two being nutritional deficiencies and hormonal variations which have significant effects on bone metabolism and turnover...

OBJECTIVE: Structural support for depressed tibial plateau fractures is receiving increasing attention. Currently, there has been little biomechanical evaluation of structural support. This work aimed to investigate the effect of structural support size and position on fracture fixation stability. METHODS: A split-depressed tibial plateau fracture model was created according to the fracture map. Cortical screws combined with structural filler were used for fracture fixation...

Intramedullary nailing is the gold standard of treatment for atypical femoral fractures, with a few reports of secondary atypical subtrochanteric femoral fractures following intramedullary nailing for atypical diaphyseal femoral fractures. However, there are no reports of secondary atypical diaphyseal femoral fractures following intramedullary nailing for atypical subtrochanteric femoral fractures. A 71-year-old woman with adult-onset Still's disease sustained a right atypical subtrochanteric femoral fracture and was treated with a mid-length intramedullary nail...

The stress measurements determined by both the overcoring (OC) and hydraulic fracturing (HF) methods in the Shuichang iron mine and Sanshandao gold mine were compared and evaluated, respectively. The results indicate that the independent OC and HF data in the two mines reveal the same dominant faulting stress regime. The σH orientations derived from the OC and HF methods in the Shuichang iron mine are dominantly oriented in the N81.1°W-N89.4°W and N77.0°E-N88.0°E, respectively, and the σH orientations yielded from the OC and HF techniques in the Sanshandao gold mine are predominantly in the N30°W-N90°W and N55...

INTRODUCTION: Given the growing emphasis on patient outcomes, including postoperative complications, in total joint arthroplasty (TJA), investigating the rise of outpatient arthroplasty is warranted. Concerns exist over the safety of discharging patients home on the same day due to increased readmission and complication rates. However, psychological benefits and lower costs provide an incentive for outpatient arthroplasty. The influence of social determinants of health disparities on outpatient arthroplasty remains unexplored...

Introduction Bone as a material varies its composition and mechanical properties throughout life. Although these variations are better understood in adulthood, there is little experimental information on the variation of these properties in early stages of development. The objective of this study is to analyze the mechanical behavior and chemical properties of cortical bone tissue from two animal species in these earliest stages. Material and methodology Twenty specimens of cortical bone were manufactured from bovine and ovine species that were in different stages of development (feeding exclusively on breast milk, in the transition period to feed or pasture, and young animals but on a solid food diet)...

OBJECTIVE: To explore the practice of prescribing and implementing early mobilisation and weight-bearing as tolerated after hip fracture surgery in older adults and identify barriers and facilitators to their implementation. METHODS: Semi-structured interviews were conducted with 20 healthcare providers (10 orthopaedic surgeons and 10 physiotherapists) from Saudi Arabian government hospitals. Data were analysed using inductive thematic analysis. RESULTS: While early mobilisation and weight-bearing as tolerated were viewed as important by most participants, they highlighted barriers to the implementation of these practices...

BACKGROUND: Pressure distribution in the ankle joint is known to be dependent on various factors, including hindfoot alignment. We seek to evaluate how hindfoot alignment affects contact pressures in the ankle joint in the setting of supination external rotation (SER) type ankle fractures. METHODS: SER fractures were created in 10 human cadaver lower extremity specimens, simulating progressive stages of injury: without fracture (step 0), SER fracture and intact deltoid ligament (step 1), superficial deltoid ligament disruption (step 2), and deep deltoid ligament disruption (step 3)...

BACKGROUND: Military recruits and athletes have high occurrence of stress fractures, with very high incidence among military recruits. Symptomatic stress fractures can be disabling in some people. This study aims at identifying pattern and distribution of such fractures in Nepal Police trainee and assess the risk factors and demographics that may help to develop the local guidelines. METHODS: This study analysed 65 police trainees who presented to the orthopaedic Out Patient Department at Nepal Police and Province Police Hospital diagnosed as a case of stress fracture from 29 December, 2020 to 29 December, 2021...

The implant material at the fracture site influences fracture healing not only from biological perspective but also from mechanical perspective. Biodegradable implants such as magnesium (Mg) based alloys have shown faster secondary bone healing properties as compared to bioinert implants such as titanium (Ti). The general reasoning behind this is the benefit of Mg from biocompatibility perspectives. We studied the effect of Ti and Mg as base materials for implants from mechanical perspectives, where we focused on the displacements at the fracture site of the tibia and their influence on the stimulus for bone healing...

It is currently a challenge to accurately predict the deformation and fracture behavior of metal parts in automobile crashes. Many studies have shown that the deformation and fracture behavior of materials are significantly affected by the stress state during automobile crashes with complex stress state characteristics. In order to further promote the application of die-cast magnesium alloys in automobiles, it is particularly important to study the material deformation and fracture behavior of die-cast magnesium alloys...

In soft electronics, anisotropic conductive adhesive films (ACFs) are the trending interconnecting approach due to their substantial softness and superior bondability to flexible substrates. However, low bonding pressure (≤1 MPa) and fine-pitch interconnections of ACFs become challenging while being extended in advanced device developments such as wafer-level packaging and three-dimensional multi-layer integrated circuit board assembly. To overcome these difficulties, we studied two types of ACFs with distinct conductive filler sizes (ACF-1: ~20 μm and ACF-2: ~5 μm)...

Tensile-compression fatigue deformation tests were conducted on AZ31 magnesium alloy at room temperature. Electron backscatter diffraction (EBSD) scanning electron microscopy was used to scan the microstructure near the fatigue fracture surface. It was found that lamellar {10-11}-{10-12} secondary twins (STs) appeared inside primary {10-11} contraction twins (CTs), with a morphology similar to the previously discovered {10-12}-{10-12} STs. However, through detailed misorientation calibration, it was determined that this type of secondary twin is {10-11}-{10-12} ST...

In order to study the multi-mode damage and fracture mechanisms of thin-walled tubular parts with cross inner ribs (longitudinal and transverse inner ribs, LTIRs), the Gurson-Tvergaard-Needleman (GTN) model was modified with a newly proposed stress state function. Thus, tension damage and shear damage were unified by the new stress state function, which was asymmetric with respect to stress triaxiality. Tension damage dominated the modification, which coupled with the shear damage variable, ensured the optimal prediction of fractures of thin-walled tubular parts with LTIRs by the modified GTN model...

The effect of hydrogen content on the deformation and fracture behavior of 27Cr-4Mo-2Ni super ferritic stainless steel (SFSS) was investigated in this study. It was shown that the plasticity and yield strength of SFSS were very susceptible to hydrogen content. The introduction of hydrogen led to a significant decrease in elongation and a concurrent increase in yield strength. Nevertheless, a critical threshold was identified in the elongation reduction, after which the elongation remained approximately constant even with more hydrogen introduced, while the yield strength exhibited a monotonic increase with increasing hydrogen content within the experimental range, attributed to the pinning effect of the hydrogen Cottrell atmosphere on dislocations...

As the central component in friction stir welding, the design and manufacture of welding tools for aluminum alloys have garnered substantial attention. However, the understanding of tool reliability during the welding process, especially in terms of fatigue performance, remains unclear. This paper focuses on the welding of AA2219-T4 as a case study to elucidate the predominant failure mode of the tool during the friction stir welding (FSW) of aluminum alloys. Experimental methods, including FSW welding and fracture morphology analysis of the failed tool, coupled with numerical simulation, confirm that high-cycle mechanical fatigue fracture is the primary mode of the tool failure...

Platinum plays a crucial role in the superior high-temperature oxidation resistance of Pt-modified nickel aluminide (PtAl) coatings. However, PtAl coatings usually serve in thermo-mechanical coupling environments. To investigate whether Pt contributes to the high-temperature mechanical properties of PtAl coating, stress rupture tests under 1100 °C/100 MPa were performed on PtAl coatings with varying Pt contents. The different coatings were obtained by changing the thickness of the electroplated Pt layer, followed by a diffusion heat treatment and the aluminizing process in the present work...

Solving the challenges facing the mining industry is crucial for shaping the global attitude towards clean energy technologies associated with critical minerals extracted from depth. One of these challenges is the well-known explosion-like fractures (rockbursts) or spalling failures associated with the initiation of internal cracks. To prevent such catastrophic failure, shotcrete, as a cement grout, is widely used in tunnel support applications. In areas where the tunnels are constructed within the limestone strata using tunnel boring machines (TBM), drilling, and/or blasting, millions of cubic meters of crushed limestone (CL) in powder form are extracted and landfilled as waste...