organic thermoelectric

Off-stoichiometric Cu-Cr-O delafossite thin films with different thicknesses were grown by metal organic chemical vapor deposition on substrates with different coefficients of thermal expansion. Seebeck thermoelectric coefficient and resistivity measurements were performed on the range of 300-850 K. A qualitative change in the temperature-dependence of the resistivity is observed at the temperature corresponding to the deposition process, where the transition from tensile to compressive strain takes place. Arrhenius plots reveal different slopes in these two thermal ranges...

Enhancing the thermoelectric transport properties of conductive polymer materials has been a long-term challenge, in spite of the success seen with molecular doping strategies. However, the strong coupling between the thermopower and the electrical conductivity limits thermoelectric performance. Here, we use polaron interfacial occupied entropy engineering to break through this intercoupling for a PEDOT:PSS (poly(3,4-ethylenedioxythiophene)-poly(4-styrenesulfonate)) thin film by using photochromic diarylethene (DAE) dopants coupled with UV-light modulation...

Ionic thermoelectric (i-TE) liquid cells offer an environmentally friendly, cost effective, and easy-operation route to low-grade heat recovery. However, the lowest temperature is limited by the freezing temperature of the aqueous electrolyte. Applying a eutectic solvent strategy, we fabricate a high-performance cryo-temperature i-TE liquid cell. Formamide is used as a chaotic organic solvent that destroys the hydrogen bond network between water molecules, forming a deep eutectic solvent that enables the cell to operate near cryo temperatures (down to -35 °C)...

The study of molecular wires facilitating long-range charge transport is of fundamental interest for the development of various technologies in (bio)organic and molecular electronics. Defining the nature of long-range charge transport is challenging as electrical characterization does not offer the ability to distinguish a tunneling mechanism from the other. Here, we show that investigation of the Seebeck effect provides the ability. We examine the length dependence of the Seebeck coefficient in electrografted bis-terpyridine Ru(II) complex films...

Exploring new near-room-temperature thermoelectric materials is significant for replacing current high-cost Bi2 Te3 . This study highlights the potential of Ag2 Se for wearable thermoelectric electronics, addressing the trade-off between performance and flexibility. A record-high ZT of 1.27 at 363 K is achieved in Ag2 Se-based thin films with 3.2 at.% Te doping on Se sites, realized by a new concept of doping-induced orientation engineering. We reveal that Te-doping enhances film uniformity and (00l)-orientation and in turn carrier mobility by reducing the (00l) formation energy, confirmed by solid computational and experimental evidence...

Donor-acceptor (D-A) copolymers doped with n-type dopants are widely sought after for their potential in organic thermoelectric devices. However, the existing structural disorder significantly hampers their charge transport and thermoelectric performance. In this Letter, we propose a mechanism to mitigate this disorder through side chain engineering. Utilizing molecular dynamics simulations, we demonstrate that strong Coulomb interactions between counterions and charged polymer backbones induce a transition in the stacking arrangement of the polymer backbones from a slipped to a vertical configuration...

BACKGROUND: Climate change and global warming are emerging as new challenges worldwide. The World Meteorological Organization has reported that the temperature is expected to rise by an average of 1.2°C between 2021-2025. This increase in temperature will expose more and more workers to extreme heat. OBJECTIVE: This study aimed to explore the possibility of using thermoelectric coolers for cooling the water circulation circuit of a cooling belt, which can be used for extended periods in high-temperature environments...

Conjugated polymers exhibit a unique portfolio of electrical and electrochemical behavior, which - paired with the mechanical properties that are typical for macromolecules - make them intriguing candidates for a wide range of application areas from wearable electronics to bioelectronics. However, the degree of oxidation or reduction of the polymer can strongly impact the mechanical response and thus must be considered when designing flexible or stretchable devices. This tutorial review first explores how the chain architecture, processing as well as the resulting nano- and microstructure impact the rheological and mechanical properties...

Developing low-cost and high-performance n-type polymer semiconductors is essential to accelerate the application of organic thermoelectrics (OTEs). To achieve this objective, it is critical to design strong electron-deficient building blocks with simple structure and easy synthesis, which are essential for the development of n-type polymer semiconductors. Herein, we synthesized two cyano-functionalized highly electron-deficient building blocks, namely 3,6-dibromopyrazine-2-carbonitrile (CNPz) and 3,6-Dibromopyrazine-2,5-dicarbonitrile (DCNPz), which feature simple structures and facile synthesis...

As a π-conjugated conductive polymer, poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is recognized as a promising environmentally friendly thermoelectric material. However, its low conductivity has limited applications in the thermoelectric field. Although thermoelectric efficiency can be significantly enhanced through post-treatment doping, these processes often involve environmentally harmful organic solvents or reagents. In this study, a novel and environmentally benign method using purified water (including room temperature water and subsequent warm water) to treat PEDOT:PSS film has been developed, resulting in improved thermoelectric performance...

A rational design, synthesis, and characterization of a new efficient versatile n-type dopant with a closed-shell electronic structure are described. By employing the tetraphenyl-dipyranylidene (DP0) framework with two 7π-electron systems modified with N,N-dimethylamino groups as the strong electron-donating substituent, we have successfully developed 2,2',6,6'-tetrakis[4-(dimethylamino)phenyl]-4,4'-dipyranylidene (DP7), a closed-shell molecule with an extremely high-lying energy level of the highest occupied molecular orbital, close to 4...

Recent research efforts have concentrated on the development of flexible and stretchable thermoelectric (TE) materials. However, significant challenges have emerged, including increased resistance and reduced electrical conductivity when subjected to strain. To address these issues, rigid semiconducting polymers and elastic insulating polymers have been incorporated and nanoconfinement effects have been exploited to enhance the charge mobility. Herein, a feasible approach is presented for fabricating stretchable TE materials by using a doped semiconducting polymer blend consisting of either poly(3-hexylthiophene) ( P3HT ) or poly(3,6-dithiophen-2-yl-2,5-di(2-decyltetradecyl)-pyrrolo[3,4- c ]pyrrole-1,4-dione- alt -thienylenevinylene-2,5-yl) ( PDVT-10 ) as the rigid polymer with styrene-ethylene-butylene-styrene ( SEBS ) as the elastic polymer...

This work focuses on the encapsulation of two organic phase change materials (PCMs), hexadecane and octadecane, through the formation of nanocapsules of the conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) obtained by oxidative polymerization in miniemulsion. The energy storage capacity of nanoparticles is studied by preparing polymer films on supporting substrates. The results indicate that the prepared systems can store and later release thermal energy in the form of latent heat efficiently, which is of vital importance to increase the efficiency of future thermoelectric devices...

Implantable bioelectronic devices (IBDs) have gained attention for their capacity to conformably detect physiological and pathological signals and further provide internal therapy. However, traditional power sources integrated into these IBDs possess intricate limitations such as bulkiness, rigidity, and biotoxicity. Recently, artificial "tissue batteries" (ATBs) have diffusely developed as artificial power sources for IBDs manufacturing, enabling comprehensive biological-activity monitoring, diagnosis, and therapy...

Geothermal power generation employing Organic Rankine Cycle (ORC) technology is a widely acknowledged and conventional approach for harnessing geothermal energy. In an innovative advancement, we propose a novel design integrating downhole thermoelectric power generation with a coaxial borehole heat exchanger. This design aims to enhance the efficiency and sustainability of geothermal energy utilization. In this innovative design, the geothermal well is divided into two distinct sections: a power generation section and a heat exchanging section, achieved through the implementation of a packer positioned from the uppermost part of the targeted zone...

This paper presents so-called thermoelectric generators (TEGs), which are considered thermal engines that transform heat into electricity using the Seebeck effect for this purpose. By using linear irreversible thermodynamics (LIT), it is possible to study the thermodynamic properties of TEGs for three different operating regimes: maximum power output (MPO), maximum ecological function (MEF) and maximum power efficiency (MPE). Then, by considering thermoelectricty, using the correspondence between the heat capacity of a solid and the metabolic rate, and taking the generation of energy by means of the metabolism of an organism as a process out of equilibrium, it is plausible to use linear irreversible thermodynamics (LIT) to obtain some interesting results in order to understand how metabolism is generated by a particle's released energy, which explains the empirically studied allometric laws...

The flexible thermoelectric technique, which can convert heat from the human body to electricity via the Seebeck effect, is expected to provide a peerless solution for the power supply of wearables. The recent discovery of ductile semiconductors has opened a new avenue for flexible thermoelectric technology, but their power factor and figure-of-merit values are still much lower than those of classic thermoelectric materials. Herein, we demonstrate the presence of morphotropic phase boundary in Ag2 Se-Ag2 S pseudobinary compounds...

Abundant conducting polymers are promising organic substances for low-temperature thermoelectric applications due to their inherently low thermal conductivities. By introducing a conducting polymer filler (PEDOT:PSS─poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonic acid)) into a representative inorganic thermoelectric matrix (Bi2 Te3 ), a bulk-phase composite (i.e., inorganic matrix/organic filler) for low-temperature thermoelectric applications is proposed. This composite hosts an interfacial energy barrier between the inorganic and organic components, facilitating controlled carrier transport based on its energy level, known as the energy filtering effect, and thus the composite exhibits a highly improved Seebeck coefficient compared to pristine Bi2 Te3 ...

Rapid developments in organic electronics demand highly conductive and freestanding (PEDOT:PSS) films. However, the synthesis of highly conductive PEDOT:PSS films requires toxic reagents, such as high-concentration acids and bases. Herein, an eco-friendly and cost-effective strategy is reported for improving the conductivity of PEDOT:PSS films through the confinement of ice crystals. The crystallization of water swelled by the film facilitated the phase separation of PEDOT and PSS, and the excess PSS in the skin layer is effectively removed...

The emerging fields of wearables and the Internet of Things introduce the need for electronics and power sources with unconventional form factors: large area, customizable shape, and flexibility. Thermoelectric (TE) generators can power those systems by converting abundant waste heat into electricity, whereas the versatility of additive manufacturing suits heterogeneous form factors. Here, additive manufacturing of high-performing flexible TEs is proposed. Maskless and large-area patterning of Bi2 Te3 -based films is performed by laser powder bed fusion directly on plastic foil...