printed electronics

In soft electronics, anisotropic conductive adhesive films (ACFs) are the trending interconnecting approach due to their substantial softness and superior bondability to flexible substrates. However, low bonding pressure (≤1 MPa) and fine-pitch interconnections of ACFs become challenging while being extended in advanced device developments such as wafer-level packaging and three-dimensional multi-layer integrated circuit board assembly. To overcome these difficulties, we studied two types of ACFs with distinct conductive filler sizes (ACF-1: ~20 μm and ACF-2: ~5 μm)...

The present study aimed to characterize the microstructure of a temporary 3D printing polymer-based composite material (Resilab Temp), evaluating its optical properties and mechanical behavior according to different post-curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 × 10 × 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on a W3D printer (Wilcos), and light-cured in Anycubic Photon for different lengths of time (no post-curing, 16 min, 32 min, and 60 min)...

The general requirement of replacing petroleum-derived plastics with renewable resources is particularly challenging for new technologies such as the additive manufacturing of photocurable resins. In this work, the influence of mono- and bifunctional reactive diluents on the printability and performance of resins based on acrylated epoxidized soybean oil (AESO) was explored. Polyethylene glycol di(meth)acrylates of different molecular weights were selected as diluents based on the viscosity and mechanical properties of their binary mixtures with AESO...

Thromboprophylaxis of hospitalized patients at risk of venous thromboembolism (VTE) presents challenges owing to patient heterogeneity and lack of adoption of evidence-based methods. Intuitive practices for thromboprophylaxis have resulted in many patients being inappropriately prophylaxed. We conducted a narrative review summarizing system-wide thromboprophylaxis interventions in hospitalized patients. Multiple interventions for thromboprophylaxis have been tested, including multifaceted approaches such as national VTE prevention programs with audits, pre-printed order entry, passive alerts (either human or electronic), and more recently, the use of active clinical decision support (CDS) tools incorporated into electronic health records (EHRs)...

Acinetobacter baumannii (A. baumannii) is a pathogenic bacterium that causes severe infections and its rapid and reliable diagnosis is essential for effective control and treatment. In this study, we present an electrochemical aptasensor based on a signal amplification strategy for the detection of A. baumannii, the high specificity and affinity of the aptamer for the target make it favorable for signal amplification. This allows for a highly sensitive and selective detection of the target. The aptasensor is based on a carbon screen-printed electrode (CSPE) that has been modified with a nanocomposite consisting of multi-walled carbon nanotubes (MWCNTs), reduced graphene oxide (rGO), chitosan (CS), and a synthesized carbon quantum dot (CQD) from CS...

Achieving sufficient bone regeneration in large segmental defects is challenging, with the structure of bone repair scaffolds and their loaded bioactive substances crucial for modulating the local osteogenic microenvironment. This study utilized digital laser processing (DLP)-based 3D printing technology to successfully fabricate high-precision methacryloylated polycaprolactone (PCLMA) bionic bone scaffold structures. Adipose-derived stem cell-engineered nanovesicles (ADSC-ENs) were uniformly and stably modified onto the bionic scaffold surface using a perfusion device, constructing a conducive microenvironment for tissue regeneration and long bone defect repair through the scaffold's structural design and the vesicles' biological functions...

In a 2023 sequential explanatory mixed-methods study in four US states, we identified barriers and facilitators experienced by Vaccines for Children (VFC) program providers in reporting vaccination data to state immunization information systems (IISs). We found the following: VFC providers value accurate, robust, and widely used IISs. IIS reporting is easier with but does not require an electronic health record. Negative interactions with IISs and VFC officials and limited practice capacity are barriers to reporting...

PURPOSE: We prospectively evaluate the short-term clinical and radiographic outcomes of the only Chinese domestically produced trabecular titanium acetabular cup(3D ACT™ cup) in primary total hip arthroplasty (THA), aiming to provide evidence-based support for its clinical application. METHODS: A total of 236 patients, who underwent primary THA using 3D ACT™ cup in the Department of Joint Surgery at our hospital between January 2017 and June 2019, were included in this study...

PURPOSE: This study aims to explore a novel scaffold for osteotendinous junction regeneration and to preliminarily verify its osteogenic and tenogenic abilities in vitro. METHODS: A polycaprolactone (PCL) scaffold with aligned and orthogonal fibers was created using melt electrowriting (MEW) and fused deposition modeling (FDM). The scaffold was coated with Type I collagen, and hydroxyapatite was carefully added to separate the regions intended for bone and tendon regeneration, before being rolled into a cylindrical shape...

OBJECTIVE: The effects of arsenic trioxide (As2 O3 ) on hepatocellular carcinoma have been documented widely. Autophagy plays dual roles in the survival and death of cancer cells. Therefore, we investigated the exact role of autophagy in As2 O3 -induced apoptosis in liver cancer cells. METHODS: The viability of hepatoma cells was determined using the MTT assay with or without fetal bovine serum. The rate of apoptosis in liver cancer cells treated with As2 O3 was evaluated using flow cytometry, Hoechst 33258 staining, and TUNEL assays...

Recent advances in materials science, device designs and advanced fabrication technologies have enabled the rapid development of transient electronics, which represents a class of devices or systems that their functionalities and constitutions can be partially/completely degraded via chemical reaction or physical disintegration over a stable operation. Therefore, numerous potentials, including zero/reduced waste electronics, bioresorbable electronic implants, hardware security, and others, are expected. In particular, transient electronics with biocompatible and bioresorbable properties could completely eliminate the secondary retrieval surgical procedure after their in-body operation, thus offering significant potentials for biomedical applications...

Semiconductor nanofilm fabrication with advanced technology is of great importance for next-generation electronics/optoelectronics. Fabrication of high-quality and perfectly oriented semiconductor thin films and integration into high-performance electronic devices with low cost and high efficiency are huge challenges. Here we exquisitely utilized the Marangoni effect to perfectly guide tin disulfide (SnS2 ) nanocoins into an ordered assembly in milliseconds, resulting in an uniaxial-oriented monolayer semiconductor film...

BACKGROUND: Recent advancements in three-dimensional (3D) printing have introduced novel materials for removable partial dentures (RPD) base fabrication, promising improved mechanical properties, and biocompatibility. MATERIALS AND METHODS: In this study, three different RPD base materials were evaluated: conventional heat-cured acrylic resin (Control), biocompatible 3D-printed resin (Test Group A), and a novel nanocomposite 3D-printed resin (Test Group B). A total of 30 standardized RPD base specimens ( n = 10 per group) were fabricated according to established protocols...

OBJECTIVES: This study compares the bacterial susceptibility to three different provisional restorations manufactured with different laboratory techniques, i.e., heat cure, CAD/CAM, and 3D printing. MATERIALS AND METHODS: Totally, 45 health patients with age group of 30-60 years undergoing complete veneer crown treatment were selected for the study and divided into three groups with 15 samples in each as Group I: the crowns were made from polymethyl methacrylate polymer fabricated by the conventional heat cure method, Group 2: the crowns were made from polymethyl methacrylate fabricated by subtractive manufacturing CAD/CAM method, and Group 3: the crowns were made from oligomers fabricated by additive manufacturing 3D printing...

OBJECTIVE: To analyze the influence of forming direction on the surface characteristics, elastic modulus, bending strength and fracture toughness of printed parts and the relationship between forming direction and force direction, and to provide scientific basis and guidance for the clinical application of oral denture base resin materials. METHODS: The 3D printing technology was used to print denture base resin samples. The shape and size of the samples referred to the current standard for testing conventional denture base materials...

Electrochemical sensors have been the subject of much research and development as of late, with several publications detailing new designs boasting enhanced performance metrics. That is, without a doubt, because such sensors stand out from other analytical tools thanks to their excellent analytical characteristics, low cost, and ease of use. Their progress has shown a trend toward seeking out novel useful nano structure materials. A variety of nanostructure metal oxides have been utilized in the creation of potentiometric sensors, which are the subject of this article...

In the current study, coated microneedle arrays were fabricated by means of digital light processing (DLP) printing. Three different shapes were designed, printed, and coated with PLGA particles containing two different actives. Rivastigmine (RIV) and N-acetyl-cysteine (NAC) were coformulated via electrohydrodynamic atomization (EHDA), and they were incorporated into the PLGA particles. The two actives are administered as a combined therapy for Alzheimer's disease. The printed arrays were evaluated regarding their ability to penetrate skin and their mechanical properties...

The utilization of robots in computer, communication, and consumer electronics (3C) assembly has the potential to significantly reduce labor costs and enhance assembly efficiency. However, many typical scenarios in 3C assembly, such as the assembly of flexible printed circuits (FPCs), involve complex manipulations with long-horizon steps and high-precision requirements that cannot be effectively accomplished through manual programming or conventional skill-learning methods. To address this challenge, this article proposes a learning-based framework for the acquisition of complex 3C assembly skills assisted by a multimodal digital-twin environment...

Timolol maleate (TML) is a beta-blocker drug that is commonly used to lower the intraocular pressure in glaucoma. This study focused on using a 3D printing (3DP) method for the manufacturing of an ocular, implantable, sustained-release drug delivery system (DDS). Polycaprolactone (PCL), and PCL with 5 or 10% TML implants were manufactured using a one-step 3DP process. Their physicochemical characteristics were analysed using light microscopy, scanning electronic microscopy (SEM), differential scanning calorimetry (DSC) / thermal gravimetric analysis (TGA), and Fourier-transform infrared spectroscopy (FTIR)...

Biomaterials denoting self-healing and versatile structural integrity are highly curious in the biomedicine segment. The injectable and/or printable 3D (3 dimensional) printing technology was explored in a few decades back, which can alter their dimensions temporarily under shear stress, showing potential healing/recovery tendency with patient-specific intervention towards the development of personalized medicine. Thus, self-healing injectable hydrogels (IHs) are stunning towards developing a paradigm for tissue regeneration...